Hi everyone, I’m finally able to sit down and spend some time on my blog, it needs a little tidying up!

Last week I shared this wonderful project and so many of you have been making your own beautiful versions.

I was inspired to make this by this Egg Holder I have, I love its size and shape and thought it would look nice on the wall in my craft room.

I think I done well recreating it with greyboard, I made the draw deeper so I can put plenty in it.

The draw comes straight out, so you have the option to not make the draw and have an open area, to hold ink pads, Nuvo Drops or anything you like.

You also have a nice amount of space at the top under the flip lid.

For a while, I was going to keep the top plain but then I decided to add some flowers and I’m so glad I did, as I think it finishes it off perfectly.

SUPPLIES USED TO MAKE THIS

2mm Greyboard available here.

My papers used are called Bird Song from Mintay.

MEASUREMENTS NEEDED TO MAKE THIS

FOR THE MAIN BOX

1 piece of 7″ x 7.1/2″ – 2mm greyboard for the back

1 piece of 3.1/2 x 7″ – 2mm greyboard for the base

1 piece of 4″ x 7.1/2 – 2mm greyboard for the flip lid

1 piece of 3.1/2 x 7″ – 2mm greyboard for the shelf

2 pieces of 2mm – 3.1/2 x 7.1/2 greyboard for the sides

1 piece of  2.3/8 x 7″ – 2mm greyboard for the front top section

FOR THE DRAW

1 piece of 3.3/4 x 6.3/4 – 2mm greyboard for the front

1 piece of 3.3/4 x 6.7/8 – 2mm greyboard for the back

2 piece of 3.1/4 x 3.3/4 – 2mm greyboard for the sides

1 piece of 3.1/4 x 6.3/4 – 2mm greyboard for the base

FOR THE MATS FOR THE MAIN BOX

1 piece of 6.7/8 x 7.3/8 to cover the back

2 pieces of 3.3/8 x 7.3/8 to cover the outside sides

2 pieces of 7″ x 2.3/8 pattern paper to cover both sides of the top front section with the mesh detail.

2 pieces of 3.7/8 x 7.3/8 to cover both sides of the lid

2 pieces of 3.1/4 x 3.1/4 to cover the inside sides of the top section

1 piece of just under 7″ x 3.1/4 to cover the bottom of the top section

1 piece of just under 7″ x 3.3/8 to cover the back of the top section

2 pieces of 3.1/4 x 3.5/8 to cover each side of the bottom section

1 piece of  3.3/8 x 6.7/8 to cover the inside bottom section

1 piece of 6.7/8 x 3.3/4 to cover the back of the bottom section

1 piece of 3.3/8 x 6.7/8 to cover the top of the bottom section.

FOR THE MATS FOR THE DRAW

1 piece of 6.3/4 x 3.1/4 paper to cover the very bottom of the draw

2 pieces of 6.7/8 x 3.5/8 to cover both sides of the back of the draw

4 pieces of 3.1/8 x 3.5/8 to cover both the in & outsides of the draw

2 pieces of 6.3/4 x 3.3/4 to cover both sides of the front of the draw

Lots of 1″ or 2″ wide strips for all the hinges.

Check out my full tutorial below to see how I made it.

As always thank you for stopping by.

Have a great day

Sam

xoxo

Disclaimer Some of the product links used are affiliated, these do not cost you extra but by using them I will receive a small % of the sales which then help me to continue bringing you great YouTube tutorials. Thank you all for your support.